温馨提示：本站仅提供公开网络链接索引服务，不存储、不篡改任何第三方内容，所有内容版权归原作者所有
AI智能索引来源：http://www.mr2.com/forums/archive/index.php/t-54878.html
点击访问原文链接

v6 headers 1mz or 3mz [Archive] - Toyota MR2 Message Board

进入原网站 导航首页
v6 headers 1mz or 3mz [Archive] - Toyota MR2 Message Board Toyota MR2 Message Board > Toyota Engine Clubs > V6 Owners Group > V6 Parts Swap > v6 headers 1mz or 3mz PDA

View Full Version : v6 headers 1mz or 3mz


Brad Bedell07-09-2010, 11:08 PMI got a batch of these made, it took them nearly 2 years to deliver. Needless to say, they don't fit quite right so I'm blowing them out for below what I paid after I ship them and eat paypal fee's.

Price is $350 for the pair shipped to the US. These will work, but you will need to work on them a little. Email me for fastest response. bradmr2 at hotmail dot com.

Header on the left in the picture below is the front. The oil filter will hit where the weld is. Solution: Dimple the tube 1/4" or so OR use an oil filter relocation kit. Potentially a shorter oil filter, but not sure what's available.

Rear header, you will need to trim off the rear v6 mount and only have a MR2 rear mount. *or use the Sienna/solara axle bracket that doesn't have the large mount attached to it.
These will work as is, but would be wise to dimple the rear crossmember or the lowest tube as it clears over. 1/4" or so would do it. The sway bar clears, but would also be wise to put a piece of rubber hose on it to prevent the occasional rattle.


*edit* This is for the headers only...No b/y-pipe. Price is $350 shipped to the US.

http://bedellracing.smugmug.com/photos/838137685_MNB6f-XL.jpg Gairloch07-09-2010, 11:53 PMPurty!

Email sent. Brad Bedell07-10-2010, 10:08 PMCouple of more pictures:

http://bedellracing.smugmug.com/photos/930315273_xNs8J-XL.jpg

http://bedellracing.smugmug.com/photos/930315224_s5cRT-XL.jpg Chris41107-12-2010, 02:45 PMNice Lime-Light08-20-2010, 11:01 AMGot anything that would fit a 3VZ lying around....? :) Brad Bedell08-20-2010, 11:41 AMNope. But I do have more of these; they need a home. Lime-Light08-20-2010, 03:17 PMWhats the plausibility of making these fit a 3VZ? Would it be a matter of cutting off the flanges and welding on stock ones, or do the pipes not match up to the ports? Forgive my ignorance but I'd be interested in a set if it's a reasonable amount of work to make them fit. Brad Bedell08-20-2010, 05:25 PMI have no clue. Just1n_mc01-15-2011, 12:43 AMI'm keen for a set of these and have sent you a PM. Brad Bedell08-07-2011, 09:27 PMI have only 3 sets left. bradmr2 at hotmail.com is the best way to reach me. Brad Bedell09-08-2013, 11:09 PMOne set of headers left. I was keeping them for myself, but it's time to let them go. I need the attic space. :) Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.

智能索引记录